灌膠機壓力桶的運用方法！
有不同種類的膠水機經常使用膠水,可以說超過同類產品,每個模型都有不同的性能,膠水涂料常用的膠水,通道結束膠機可以使用,只能評論的一些比較常見的膠水,滿足一些基本的涂料行業,壓力桶的使用方法。
There are different types of glue machines that often use glue, which can be said to be more than the same products. Each model has different performance. The glue commonly used for glue coating can be used at the end of the channel. Only some common glue can be commented on to meet the use methods of some basic coating industries and pressure buckets.
一、普通膠水型
I. ordinary glue type
膠機常用的涂層膠分別用銀膠、紅膠、熱熔膠、硅膠、AB膠、快干膠、焊錫膏、環氧天然橡膠、填充底部的橡膠、乙烯基、厭氧膠、耐高溫膠、白膠等等,這些都是常用的涂層膠,膠與通道膠機可以使用,但需要更換一些配件,可以滿足生產的需要,上膠閥對上膠有少量的要求較高，類似于硅膠、熱熔膠、紅膠、厭氧膠等需要特殊上膠閥設備才能真正上膠的末端要求。
The coating glue commonly used in glue machine is silver glue, red glue, hot melt glue, silica gel, AB glue, quick drying glue, solder paste, epoxy natural rubber, rubber filled with bottom, vinyl, anaerobic glue, high temperature resistant glue, white glue, etc. These are commonly used coating glue. Glue and channel glue machine can be used, but some accessories need to be replaced to meet the production needs. There is a small amount of glue on glue valve High requirements, similar to silica gel, hot-melt glue, red glue, anaerobic glue, etc. need special glue valve equipment to really glue the end requirements.
二、使用壓力斗要注意問題
II. Precautions in using pressure bucket
這些類型的膠水要求適用于灌裝壓力桶嗎?對特定的需求,自動化生產是不需要通過更換可能每次膠,使用氣動式壓力桶來滿足通道膠機連續膠的要求,只有壓力桶必須注意使用方法,或特別容易出現膠水供應不足,導致沒有膠水,膠水使用膠水每個日出生產是非常大的。
Are these types of glue requirements applicable to filling pressure barrels? For specific needs, automatic production does not need to replace every glue. Pneumatic pressure barrels are used to meet the continuous glue requirements of the channel glue machine. Only the pressure barrels must pay attention to the use method, or they are particularly prone to insufficient glue supply, resulting in no glue. Every sunrise production with glue is very large.
三、使用灌桶
III. use of buckets
如何使用氣動壓力鼓的通道填料使用?相對短暫,要了解膠水的性質,然后觀察濃度條件下,特別容易冷凝式連續混合,避免冷凝,更高水平的膠是一樣的,有一個低降水的膠水,膠水濃度還需要添加混合,然后加入膠桶式氣壓,氣壓管、壓力釋放閥、防爆閥、等,密封,以避免泄漏,然后接軟管膠機、這樣的基本是連通的。先在壓力桶中充分充氣后，再用槽膠機將膠水泵出，以免造成膠水間歇時產生問題。
How to use the channel packing of the pneumatic pressure drum? It is relatively short. First, understand the nature of the glue, and then observe the condition of concentration. It is very easy to mix continuously with condensation to avoid condensation. The higher level glue is the same. There is a glue with low precipitation. The glue concentration also needs to be mixed, and then add the rubber barrel type air pressure, air pressure pipe, pressure relief valve, explosion-proof valve, etc. to seal to avoid condensation No leakage, then connect the hose rubber machine, which is basically connected. First, fully inflate the pressure barrel, and then pump out the glue with the slot glue machine, so as not to cause problems when the glue is intermittently.
上一篇：雙組份打膠機開機報警的解決方法！
下一篇：打膠機如何防止膠水沉淀？
