中空玻璃打膠機斷膠解決方法！
中空玻璃打膠機斷膠解決方法：
Solution to broken glue of hollow glass dispenser:
要進行 中空玻璃打膠機排除問題，然后針對性解決斷膠的問題。
The first choice is to eliminate the problem of hollow glass gluing machine, and then solve the problem of glue breaking.
作為中空玻璃制作設備的 中空玻璃打膠機中丁基膠涂布機，在使用中會因為一點小問題影響使用，比如更常見的：
As a hollow glass production equipment, the butyl glue coating machine in the hollow glass gluing machine will affect the use due to a small problem, such as the most common:
中空玻璃打膠機為了增加制作效率調整是輸送帶速度很快，出膠量沒法調整，導致斷斷續續的原因之一。
In order to increase the production efficiency, the adjustment of the first hollow glass gluing machine is one of the reasons that the speed of the conveyor belt is very fast, and the glue output cannot be adjusted, resulting in intermittent.
第二 對于膠缸和膠頭的溫度沒有設置好，到時有的膠沒有達到應有的溫度，導致出現鋸齒類的情況。
Second, the temperature of the rubber cylinder and the rubber head is not set properly, and some rubber fails to reach the proper temperature at that time, resulting in sawtooth.
第三 中空玻璃打膠機建議把溫度調整到合適的溫度，使丁基膠化掉，這樣幾乎不會出現以上問題。
The third insulating glass gluing machine suggested that the temperature should be adjusted to a suitable temperature to make butyl gel off, so that the above problems would hardly occur.
第四 如果是從中空玻璃打膠機剛開始使用到現在一直是這種情況 膠頭出膠口有毛刺 膠頭一般有兩種 膠口處有槽和無槽兩種
Fourth, if it's from the beginning of using the hollow glass dispenser to now, it's always the case that the rubber head has burr at the rubber outlet, and there are generally two types of rubber head: grooved and grooveless
第五 換膠以后出現這種情況 溫度到達上限以后 出膠不正常 膠口處膠沒有完全融化 手動排出一部分膠 也就是打幾個框子 將壓力調大 多打幾個框子 將膠缸內的膠擠實。
After the fifth rubber change, when the temperature reaches the upper limit, the glue at the abnormal rubber outlet does not melt completely, and part of the glue is discharged manually, that is to say, several frames are set to adjust the pressure, mostly several frames are set to compact the glue in the rubber cylinder.
第六 雙組份打膠機采購的丁基膠質量差，配置成本低，雜質堵塞引起的。
The quality of butyl rubber purchased by the sixth two-component beater is poor, the configuration cost is low, and the impurities are blocked.
第七 放膠后沒有進行放氣。
After the seventh dispensing, there was no bleeding.
上一篇：高速點膠機的產品特點以及使用方法！
下一篇：中空玻璃打膠機生產效率高不高？
