打膠機組成部分的五點保養事項
隨著社會的發展,我們進入了自動化時代,由于自動化機器給人們帶來了較大地方便，雙組份打膠機就是專門對流體進行控制,并將流體點滴、涂覆于產品表面或產品內部的自動化機器，下面小編為大家介紹
濟南雙組份打膠機組成部分是怎樣保養的吧，
With the development of society, we have entered the era of automation. Because automation machines have brought great convenience to people, two-component glue dispenser is an automatic machine that controls the fluid and drips and coats the fluid on the surface or inside of the product. The following sections will introduce how to maintain the components of Jinan two-component glue dispenser,
1，兩個馬達的加油，主馬達與輔料馬達進氣口均安裝有油霧器,當其中的油低于低端刻線時應拆下油杯加注10號機油，如果油霧器不滴油或者馬達嚴重缺油時可將主馬達進氣管與馬達連接處的活接拆掉,用油槍想里面加油,輔料馬達可將其端蓋螺母擰開加油，
1. For oil filling of the two motors, the air inlets of the main motor and auxiliary motor are equipped with oil foggers. When the oil in the oil foggers is lower than the low end reticle, the oil cup should be removed and 10 # engine oil should be added. If the oil foggers do not drip oil or the motor is seriously short of oil, the union joint at the connection between the main motor air inlet pipe and the motor can be removed, and the oil gun can be used to fill the inside. The auxiliary motor can unscrew its end cap nut for oil filling,
2，主泵,輔料泵,配比泵經過一段時間的使用后會有膠從里面滲漏出,流到油碗里，可以把膠清理掉,加注機油，用十字螺絲刀類頂住主,輔兩泵油碗下端的圓孔處按順時針方向緊固油碗;配比泵油碗用扳手擰緊即可，
2. After using the main pump, auxiliary material pump and proportioning pump for a period of time, glue will leak out from the inside and flow into the oil bowl. You can clean the glue, add oil, and use a cross screwdriver to counter the main pump and the auxiliary pump. Tighten the oil bowl clockwise at the round hole at the lower end of the oil bowl; Tighten the matching pump oil bowl with a wrench,
3，閥的注油用油槍向閥的小孔注油,可以防止生銹，
3. The oil gun is used to inject oil into the small hole of the safety valve to prevent rust,
4，Y型過濾器其位置在輔料泵出口處,清洗時將端蓋擰下,用煤油浸泡,用牙刷類刷子刷干凈，安裝時將網放在端蓋里用手擰到底,再用扳手擰緊，用一組膠洗一次,如無雜質兩組膠洗一次,靈活掌握，
4. The Y-type filter is located at the outlet of the auxiliary material pump. When cleaning, unscrew the end cover, soak it in kerosene, and brush it clean with a toothbrush. During installation, put the net in the end cover and screw it to the end by hand, then tighten it with a wrench, and wash it once with one set of glue. If there is no impurity, wash it once with two sets of glue, and you will be flexible,
5，大過濾器其位置在高壓表B表右下,擰下回流閥下方膠管,擰下過濾器,將網及網芯取出,彈簧、取出,刷干凈,將彈簧小孔套在網芯的凸點上，倒著裝入器體后轉過來擰在膠機上，用3-5組洗一次,如無雜質,靈活掌握。
5. The large filter is located at the bottom right of the high pressure gauge B. Unscrew the rubber hose under the return valve, unscrew the filter, take out the screen and the screen core, take out the spring, brush it clean, cover the small spring hole on the convex point of the screen core, install it upside down into the device body, turn it around and screw it on the glue machine, and wash it once with 3-5 groups. If there is no impurity, master it flexibly.
These are the five points about the maintenance of the glue dispenser components. If you have any questions or needs, you can come to our website at any time http://www.vrqf.com.cn Message consultation!
上一篇：雙組份打膠機阻塞的原因以及解決方案
下一篇：雙組份打膠機在使用中會出現怎樣的問題？
