雙組份打膠機阻塞的原因以及解決方案
隨著市場競爭的日益激烈，一些制造商運用殘次的丁基膠，其間的雜質很多。假如長時刻運用，
雙組份打膠機的膠槍會被阻塞。那咱們該怎么辦呢?
With the increasingly fierce market competition, some manufacturers use defective butyl rubber, which has many impurities. If it is used for a long time, the glue gun of the two-component glue dispenser will be blocked. So what should we do?
雙組份打膠機阻塞的原因：
Reasons for blocking of two-component sealant dispenser:
1.在涂膠過程中，中止時刻較長，或多次堆集，而且在上膠結束時無法完成清潔，特別是在夏日溫度較高時。
1. In the process of gluing, the center stops for a long time or accumulates for many times, and the cleaning cannot be completed at the end of gluing, especially when the temperature is high in summer.
2.AB成分的氣壓缺乏，導致混合不均勻，凝膠緩慢，簡單發生顆粒
2. Lack of air pressure of AB component leads to uneven mixing, slow gel and simple particles
3.B組件未經檢查和清潔。B成分對水蒸氣敏感。由于運送和儲存環境等偶爾因素，B組分的外表可能會結皮，外殼的一部分被壓入管道中，這很簡單發生顆粒。
3. Component B is not inspected and cleaned. Component B is sensitive to water vapor. Due to occasional factors such as transportation and storage environment, the appearance of component B may be skinned, and part of the shell is pressed into the pipe, which is simple to cause particles.
4.過濾器和單向止回閥長時刻未清洗。
4. The filter and one-way check valve have not been cleaned for a long time.
5.B組件壓板上的O形圈，運用時刻長，松動。
5. The O-ring on the pressing plate of B component has been used for a long time and is loose.
雙組份打膠機阻塞解決方案：
Blocking solution for two-component sealant dispenser:
1、斷開膠水需求花費多長時刻，主張?jiān)跀嚅_時刻之前，依據每天的溫度和濕度的不同，在每天施加膠水之前丈量剝離時刻。另外，目前的客戶常常要求膠水的固化時刻要快，中止時刻要長一些，而且簡單引起顆粒的呈現。
1. How long does it take to disconnect the glue? It is recommended to measure the stripping time before disconnecting the glue according to the temperature and humidity of each day. In addition, current customers often require that the curing time of glue should be fast, the stopping time should be longer, and the particles simply appear.
2、簡單的處理辦法是運用刮刀清潔外殼，而不影響膠水的運用。
2. A simple solution is to use a scraper to clean the shell without affecting the use of glue.
3、主張定期清潔過濾器，單向止回閥，靜態混合器和膠槍。
3. It is recommended to clean the filter, one-way check valve, static mixer and glue gun regularly.
The products produced by our company have good stability, high efficiency and convenient maintenance. Pay attention to our website http://www.vrqf.com.cn The manufacturer sincerely looks forward to your call and consultation!
上一篇：打膠機工作完后中空膠固化慢怎么回事
下一篇：打膠機組成部分的五點保養事項
